| Counter Over - Acid Volume |
Description: Actual amount of hydrochloric or phosphoric acid (wet chemistry system) used exceeds value set in “Maintenance” screen.
Resolution: Replenish the hydrochloric or phosphoric acid in the acid container. Then clear the Acid Usage Volume counter in the “Maintenance” screen.
|
| Counter Over - ASI Tubing Pump |
Description: Actual ASI pump operation time exceeds value set in “Maintenance” screen.
Resolution: Replace the tubing pump. Then clear the ASI Tubing Pump counter in the “Maintenance” screen.
|
| Counter Over - Combustion Tube Sample Injection Volume |
Description: Actual volume of sample injected into combustion tube exceeds value set in “Maintenance” screen.
Resolution: Either perform catalyst regeneration or replace the catalyst and combustion tube. Then clear the Combustion Tube Sample Injection Volume counter in the “Maintenance” screen.
|
| Counter Over - Dilution Water Volume |
Description: Actual amount of dilution water used exceeds value set in “Maintenance” screen.
Resolution: Replenish the water in the dilution water container. Then clear the Dilution Water Usage Volume counter in the “Maintenance” screen.
|
| Counter Over - IC Tubing Pump |
Description: Actual IC pump operation time exceeds value set in “Maintenance” screen.
Resolution: Replace the tubing pump. Then clear the IC Tubing Pump counter in the “Maintenance” screen.
|
| Counter Over - Persulfate Volume |
Description: The volume of oxidizing reagent exceeds the amount set in the “Maintenance” screen.
Resolution: Replenish the oxidizing reagent. Then clear the Persulfate Volume counter in the “Maintenance” screen.
|
| Counter Over - Syringe Stroke Number |
Description: Actual number of syringe strokes performed exceeds value set in “Maintenance” screen.
Resolution: Replace the plunger tip. Then clear the Syringe Stroke Number counter in the “Maintenance” screen.
|
| Error!! 8-Port Valve Position Detection |
Description: The 8-port valve is not operating normally due to clogging inside of the sample injector 8-port valve, etc.
Resolution: Switch off the instrument, and remove the rotor from the 8-port valve. Remove any particles found in the 8-port valve and wash valve.
|
| Error!! ASI Arm Horizontal Movement |
Description: The ASI-V arm is not operating normally in the horizontal direction.
Resolution: Switch off power to the TOC-V instrument. After switching on the power and running the instrument again, see if the same error is generated. Since the problem is unrelated to the TOC-V main unit, remove the ASI-V from the main unit, and perform operations using the TOC-V main unit alone until normal operation of the ASI-V is restored.
|
| Error!! ASI Arm Horizontal Position Detection |
Description: The ASI-V arm is not operating normally in the horizontal direction.
Resolution: Switch off power to the TOC-V instrument. After switching on the power and running the instrument again, see if the same error is generated. Since the problem is unrelated to the TOC-V main unit, remove the ASI-V from the main unit, and perform operations using the TOC-V main unit alone until normal operation of the ASI-V is estored.
|
| Error!! ASI Arm Vertical Movement |
Description: The ASI-V arm is not operating normally in the vertical direction.
Resolution: Switch off power to the TOC-V instrument. After switching on the power and running the instrument again, see if the same error is generated. Since the problem is unrelated to the TOC-V main unit, remove the ASI-V from the main unit, and perform operations using the TOC-V main unit alone until normal operation of the ASI-V is restored.
|
| Error!! ASI Arm Vertical Position Detection |
Description: The ASI-V arm is not operating normally in the vertical direction.
Resolution: Switch off power to the TOC-V instrument. After switching on the power and running the instrument again, see if the same error is generated. Since the problem is unrelated to the TOC-V main unit, remove the ASI-V from the main unit, and perform operations using the TOC-V main unit alone until normal operation of the ASI-V is restored.
|
| Error!! ASI Turntable Position Detection |
Description: The ASI-V turntable position could not be detected. Either the turntable is not properly seated in the rack, or some object may be blocking a position detection notch on the periphery of the rack.
Resolution: Switch off power to the TOC-V main unit. Make sure the ASI-V is properly seated in the rack, and remove any objects that may be blocking the position detection notch on the periphery of the rack. After eliminating the cause of the problem, place the cover on the ASI-V, and switch on the power to the instrument again.
|
| Error!! FLASH ROM |
Description: An error occurred while writing to the memory circuit.
Resolution: Switch off power to the instrument. Contact your Shimadzu representative.
|
| Error!! IC Slider |
Description: The IC slider is not operating normally due to particles wedged between the moving parts, etc.
Resolution: Switch off the instrument, inspect the slider and remove any foreign particles from the slider mechanism. Then switch on the power again.
|
| Error!! Oven Overheating |
Description: The oven became overheated.
Resolution: With the power ON, wait approximately 20 minutes for the oven temperature to decrease then switch OFF the instrument. After switching on the power and running the instrument again, see if the same error is generated.
|
| Error!! Oven Temperature Sensor |
Description: The oven temperature does not rise.
Resolution: Switch off power to the instrument. After switching on the power and running the instrument again, see if the same error is generated.
|
| Error!! Pressure Sensor 2 |
Description: A problem with the pressure sensor (for carrier gas) of the carrier gas control unit was detected.
Resolution: Switch off the instrument. Turn on the power again, operate the instrument, and verify whether the same error occurs again.
|
| Error!! Pressure Sensor 3 |
Description: A problem with the pressure sensor (for sparge gas) of the carrier gas control unit was detected.
Resolution: Switch off the instrument. Turn on the power again, operate the instrument, and verify whether the same error occurs again.
|
| Error!! Syringe Operation |
Description: The syringe is not operating normally due to clogging of the tubing connected to the 8-port valve, etc.
Resolution: Switch off the instrument, and remove any foreign particles from the line, etc. After switching on the power and running the instrument again, see if the same error is generated.
|
| Error!! Syringe Position Detection |
Description: The syringe is not operating normally.
Resolution: Switch off power to the instrument. After switching on the power and running the instrument again, see if the same error is generated.
|
| Error!! Syringe Zero Point Detection |
Description: The syringe is not operating normally.
Resolution: Switch off the instrument. After switching on the power and running the instrument again, see if the same error is generated.
|
| Error!! TC Slider |
Description: The TC slider is not operating normally due to particles wedged between the moving parts, etc.
Resolution: Switch off the instrument, inspect the slider and remove any foreign particles from the slider mechanism. Then switch on the power again.
|
| Error!! TN Reactor Temperature |
Description: The TNM-1 reactor temperature does not rise.
Resolution: Switch off power to the TOC-V main unit. After switching on the power and running the instrument again, see if the same error is generated.
|
| Oven temperature too low. Cannot regenerate catalyst. |
Description: Oven temperature too low. Cannot regenerate catalyst.
Resolution: Wait for the oven temperature to rise before executing the catalyst regeneration procedure.
|
| Syringe Zero Point Correction failed. |
Description: Syringe zero point correction could not be performed. Syringe is not properly installed.
Resolution: Properly install the syringe. Then execute Syringe Zero Point Correction in the “Maintenance” screen.
|
| There is no vial rack. |
Description: Operation cannot continue because there is no vial rack in the turntable.
Resolution: Install a vial rack, and then execute the operation.
|
| Vial rack type mismatch. |
Description: The vial rack type set in the parameters does not match the type actually installed.
Resolution: Verify the type of vial rack installed in the ASI-V, and then set the vial rack type in the “Parameters” screen.
|
| Vial rack type not specified. |
Description: The analysis parameters cannot be validated because the vial rack type has not been specified.
Resolution: Set the vial rack type in the “Parameters” screen.
|
| WARNING: ASI cover open detected. Please close the cover. |
Description: The ASI-V cover is open. Operation of the ASI-V has been halted as a safety measure.
Resolution: Close the ASI-V cover.
|
